How To Compression Test A Dirt Bike

Performing a compression test on a dirt bike's engine can tell a lot and it's something anyone who rides should do occasionally as this gives you a better feel of the engine's top end condition than "feeling the kick", Doing this can serve two purposes. First, it can give you an indication of how close you are getting to needing a top end freshening, secondly it can tell you whether or not any problems you may be having with the performance of the dirt bike such as hard starting, or low power are related to low compression.

This is a pretty simple and straight forward procedure as you'll see below, so whenever you freshen up the top end on a dirt bike, or have a few hours on the top end, it's a good idea to perform a compression test, as well as after breaking in a new set of piston & ring(s), then Record the Reading by scratching it in yourself in pen on either our Advanced Setup Log or Basic Setup Log

In the future, when you check the compression readings, if the pressure drops 20% from the reading that you noted after the break in period of a fresh top-end, this would indicate that the motor likely needs a tear down to check the condition of the top end, which includes the piston, piston ring(s), exhaust valve with it's related components on a 2 stroke, or the cylinder head and valve train on a 4 stroke, as well as the cylinder's condition on a 2 or 4 stroke.

Note: Some dirt bikes may require some disassembly, such as removal of the fuel tank so as to be able to screw the hose into the cylinder head at a straight angle and not kink the hose or damage the soft aluminum threads dropping shavings into the cylinder. If you can't easily thread the compression tester into the spark plug hole, be sure to remove anything in the way so as to allow access.

Before You Perform A Compression Test...

If It's a
4 Stroke...

If this is a 4 stroke dirt bike we're working on, it's not going to be possible to base your readings off of the suggestions listed below.

Due to the auto decompression release mechanism found on 4 stroke dirt bikes, you're going to need a service manual specific to that dirt bike as you can then obtain the true recommended pressure by the reading to determine the condition of the top end on a 4 stroke.

Picture of a spark plug
  • Make sure the dirt bike is clean It's important there's no dirt or water near the spark plug or coil pack on 4 strokes otherwise dirt or grit could get into the cylinder upon removal of the spark plug which is never good and leads to problems such as scoring of the cylinder walls and accelerated wear of the piston & rings, among other parts not mentioned.
  • Turn the gas off at the fuel petcock.
  • Ensure that the air filter is clean and in good condition.
Picture of a 2 stroke dirt bike's top end.
  • If necessary, remove the fuel tank as this will allow you unobstructed access to the spark plug, and you'll be able to thread a compression tester (Available at Auto Parts Stores) into the cylinder head without any sharp angles being placed on the hose, as well as allowing you to inspect the cables and hoses for any under tank chafing or other damage.
  • Finally... Remove the spark plug, and using the appropriate hose or adapter with the appropriate thread size and pitch on the compression tester's hose end to mate the threads in the cylinder head, thread the compression tester hose into the spark plug hole and tighten it finger tight, or just enough so that the o-ring or gasket which seals the compression tester to the cylinder head is making contact and becomes slightly compressed.
Keep the Top End in it's Best Condition by
Staying On Top of the Air Filter's Maintenance

Performing the Compression Test

  • For the following steps and assuming everything above has been covered, hold the throttle wide open with the engine stop / kill button depressed, or have the engine run switch turned to OFF.

Note: If you're working with an electric start motorcycle, you'll likely need to leave the engine run switch turned to "ON" so as to be able to use the starter for turning the engine over, just be sure to disable the ignition system by disconnecting the primary lead from the ignition coil (small single wire or weather proof electrical connector) and Waterproof the Electrical Connections at reassembly.

Picture of a compression gauge at 210 psi

Next, with the throttle held wide open, Kick the engine over, (or by using the electric start as can be found on some models) turn the engine over until the needle on the gauge of the compression tester peaks at it's maximum pressure and record this reading for future reference.

The ideal pressures for an average 2 stroke dirt bike at sea level that is not heavily modified should be in the vicinity of the numbers below.

  • A 50cc, 60cc, 80cc, 100cc, 125cc 200cc or 500cc should be able to squeeze out a reading of 120-190 PSI.
  • A 250cc should be in the neighborhood of 170-240 PSI.
If It's a 2 Stroke You're Working On and It's Low on Compression,
Here's Everything You Need to Know to Rebuild the Top End Yourself

If you're unable to reach a satisfactory compression reading, or there's a 20% difference (or more) from the reading you obtained after breaking in a new top end, this may be an indication that the top end is in need of being rebuilt.

If it's determined that the top end IS in need of being rebuilt, you should get a service manual specific to the dirt bike, and / or refer to our article on rebuilding the top end on a 2 stroke, then disassemble the top end to check the condition and clearances of parts as detailed in the factory service manual, replacing parts that are worn beyond the service limits stated, or have a clear indication of wear, as well as at a minimum, always replace the piston ring(s) upon disassembly no matter of their physical appearance or measurement.

After finishing up with the compression test, (provided that the pressure reading looks good), replace the spark plug with a new one of the correct type and heat range, then put everything back together and check out these:
Dirt Bike Maintenance Articles

Be The First To Comment On This

Hang Tight, Google's Determining If You're Legit...

Readers Rides
From Our Free Classifieds

Instantly See Your Dirt Bike Here Absolutely Free Of Charge
...& Remove Or Renew It Whenever You Want...
No Questions Asked

  • You Maintain Legit Full Control Of Your Motorcycle's Listing
  • Create Your Ad In Seconds & Instantly See & Edit Your Ride Live
  • Trusted & Easier With Greater Privacy Than Craigslist Or Cycle Trader
Popular FAQ's
Q: What Happens When I Create An Ad?
A: Exactly what you'd expect. An Ad just like these will be created based on the information and photos you provided, exactly as you provide it, Complete with your own User Interface (UI) for editing, removing or renewing your ad(s).
Q: How Do I Edit, Update, Renew Or Deactivate My Ad?
A: Easy, Just click where you want to edit and make your changes on the live site, or alternatively make any changes within your automatically generated UI.
Q: What Happens After 30 Days?
A: Your Ad and photos are removed from public view and renewing your ad is as easy as editing or removing it from your automatically generated UI.
Q: Do You Share Or Sell My Info?
A: NO, And not only are you not revealing anything you wouldn't publicly share elsewhere, There's not enough $ to interest us in anything that would tarnish our reputation.

You'll Cherish The Integrity Of This Moto Inspired Wizard

Please Correct The Fields Highlighted In Red

Mic Icon
📷Securely Select Or Capture Up To 4 Photos
Preexisting Photos Can Be Dropped Here & Preview Images Appear Here

Click To Reveal Steps
Ads Auto Expire in 30 Days & Use Of Our Site Acknowledges Acceptance of Our Privacy Policy

Watch the Simplicity Of Adding Your Motorcycle Here but Hang Tight, There's A Better Version Coming

We're In It To Win It

With Our Classifieds, You don't install or have to sign up for anything, nor do you reveal any details you wouldn't make public knowledge elsewhere.

Afterall, If Google & eBay Have Trusted Me Since 2009, Shouldn't You?

Questions? Call Or Txt Stuart @ 352-538-2403